Free 2025 NACE-CIP1-001 Dumps 100 Pass Guarantee With Latest Demo
Prepare NACE-CIP1-001 Question Answers Free Update With 100% Exam Passing Guarantee [2025]
NEW QUESTION # 14
If a Thermoset coating is heated it will:
- A. Harden and return to its original hardness when cooled
- B. Soften when heated and retain its softness when cooled
- C. Harden and retain its hardness when cooled
- D. Soften when heated and return to its original hardness when cooled
Answer: C
NEW QUESTION # 15
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 90% of the specified maximum thickness
- B. 80% of the specified minimum thickness
- C. 100% of the specified maximum thickness
- D. 70% of the specified maximum thickness
Answer: B
NEW QUESTION # 16
ISO SA 3 is directly equivalent to:
- A. None of the above
- B. NACE No. 3/SSPC SP 6
- C. NACE No. 2/SSPC SP 10
- D. NACE No. 1/SSPC SP 5
Answer: A
NEW QUESTION # 17
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. a detailed checklist and document the lack of a standard.
- B. their best judgment based on similar projects and specifications.
- C. NACE 2/SSPC SP10
- D. a recognized industry standard like SSPC-PA 2 that is broadly accepted
Answer: D
NEW QUESTION # 18
Surface profile describes:
- A. The initial condition of the surface prior to abrasive blasting
- B. The general condition of the surface required after abrasive blasting
- C. The level of surface cleanliness required after abrasive blasting
- D. The level of surface roughness required after abrasive blasting
Answer: D
NEW QUESTION # 19
Prior to using Inspection Tools the inspector must:
- A. Be trained on how to use the instrument
- B. Ensure the instrument is within calibration parameters
- C. a), b) & c)
- D. Read the manufactures' instructions
Answer: C
NEW QUESTION # 20
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Power tools
- B. Abrasive blast nozzles
- C. Hand tools
- D. Airless spray equipment
Answer: A
NEW QUESTION # 21
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Meet with the prospective employer to determine the scope of your role
- B. Review the NACE Attestation prior to making a decision
- C. Accept the assignment without hesitation
- D. Advise the prospective employer that you cannot accept the position
Answer: A
NEW QUESTION # 22
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor and Owner's representative
- B. Document the problem and advise the Contractor
- C. Break the blisters to see what's inside
- D. Extract any liquid that may be inside the blister and send it to the lab for further analysis
Answer: A
NEW QUESTION # 23
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. Low Surface Temperature
- B. High Relative Humidity
- C. High Surface Temperature
- D. Low Relative Humidity
Answer: D
NEW QUESTION # 24
ISO SA 2 is defined as:
- A. Near White Metal Blasting
- B. Light Blast Cleaning
- C. Thorough Blast Cleaning
- D. Very Thorough Blast Cleaning
Answer: C
NEW QUESTION # 25
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Review the relevant standard with the Contractor
- C. Permit coating to take place so as not to lose the blast
- D. Shut the job down
Answer: B
NEW QUESTION # 26
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Galvanic Corrosion
- B. Atmospheric Corrosion
- C. General Corrosion
- D. Localized Corrosion
Answer: A
NEW QUESTION # 27
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 3
- B. Level 1
- C. Level 4
- D. Level 2
Answer: A
NEW QUESTION # 28
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks and consult the Owner's representative for direction
- B. Keep doing the checks regardless
- C. Skip the checks as you are. confident the blast pressure is OK
- D. Skip the checks and just record the same readings as you have been getting
Answer: A
NEW QUESTION # 29
Removal of welds splatter is required:
- A. When ISO abrasive blast standards are specified
- B. On every job
- C. When NACE/SSPC abrasive blast standards are specified
- D. When specifically identified in the owner's specification
Answer: D
NEW QUESTION # 30
The Inspector should record the serial numbers of inspection instruments:
- A. Only when verifying accuracy of the instrument
- B. Only if the specification requires it
- C. Only if the instrument is suspected of not working properly
- D. Each time the instrument is used
Answer: D
NEW QUESTION # 31
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. At all times
- B. In the field only
- C. In the office only
- D. Only if the specification requires it
Answer: A
NEW QUESTION # 32
What is used to determine compressed air cleanliness?
- A. Needle pressure gauge
- B. Psychrometer
- C. Blotter test
- D. Profilometer
Answer: D
NEW QUESTION # 33
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Call your supervisor
- B. Advise the Contractor of your readings
- C. Advise the Contractor he can proceed
- D. Advise the Contractor he cannot proceed
Answer: B
NEW QUESTION # 34
The main responsibilities of the inspector are to
- A. observe and report the quality of the work performed.
- B. direct and perform the work stated in the specification.
- C. observe and direct the work of the contractors.
- D. demonstrate to the contractor how to apply the coating.
Answer: A
NEW QUESTION # 35
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Default to the owner's Inspection and Test Plan
- B. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- C. Bring the matter up at the pre-job conference
- D. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
Answer: C
NEW QUESTION # 36
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Check the PPE used by the Applicators
- B. Assume the role of the Safety Inspector
- C. Act in accordance with the site safety requirements and set an example
- D. Check the credentials of the Safety Officer on site
Answer: C
NEW QUESTION # 37
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. what materials were used.
- B. when the coating will be reapplied.
- C. how the item was coated.
- D. what items were coated.
Answer: C
NEW QUESTION # 38
......
NACE-CIP1-001 Coating Inspector Level 1 certification is a valuable credential for individuals who work in the coatings and corrosion control industry. Coating Inspector Level 1 certification demonstrates a level of expertise in coating inspection and gives employers and clients confidence in the individual’s ability to perform their job duties. With proper preparation and training, individuals can successfully pass the NACE-CIP1-001 exam and earn this globally recognized certification.
Dumps Real NACE NACE-CIP1-001 Exam Questions [Updated 2025]: https://actualtests.test4engine.com/NACE-CIP1-001-real-exam-questions.html